Hello,
here is my work from the last week. Next i will print the rear parts. And when the screws are delivered, i will build everything together.
Agera RS powered by Spezialbenzin
-
- Posts: 4
- Joined: Fri Jun 28, 2019 3:07 pm
Agera RS powered by Spezialbenzin
- Attachments
-
- IMG_20190713_164139.jpg (3.84 MiB) Viewed 4351 times
Greetings from Germany,
Jürgen
Jürgen
Re: Agera RS powered by Spezialbenzin
Hi there,
nice build so far. Do you have a list of the screw sizes you ordered for yours as want to order mine.
Thanks
nice build so far. Do you have a list of the screw sizes you ordered for yours as want to order mine.
Thanks
-
- Posts: 4
- Joined: Fri Jun 28, 2019 3:07 pm
Re: Agera RS powered by Spezialbenzin
Hi,
i ordered the M2 Screws in different sizes like 10, 16 and 30mm and will cut them like Olle explained it.
i ordered the M2 Screws in different sizes like 10, 16 and 30mm and will cut them like Olle explained it.
Greetings from Germany,
Jürgen
Jürgen
-
- Posts: 4
- Joined: Fri Jun 28, 2019 3:07 pm
Re: Agera RS powered by Spezialbenzin
Since I only got the ball connectors from Tamiya, I had to make the Bearing Hubs narrower and reprint.
Which balls did you use?
Sorry, but i can not load up a pic There is a report: Sorry, the board attachment quota has been reached.
Which balls did you use?
Sorry, but i can not load up a pic There is a report: Sorry, the board attachment quota has been reached.
Greetings from Germany,
Jürgen
Jürgen
Re: Agera RS powered by Spezialbenzin
Hi,
There was an attachment limit for the whole forum that I have changed now so now it should be Ok (for a while at least
)
I’m not sure exactly which of the balls I used, I will check when I get home. I had a lot of them for some time before I used them so they got mixed up.
There was an attachment limit for the whole forum that I have changed now so now it should be Ok (for a while at least

I’m not sure exactly which of the balls I used, I will check when I get home. I had a lot of them for some time before I used them so they got mixed up.
Re: Agera RS powered by Spezialbenzin
Hi Spezialbenzin,
I would ask you one the facebook group, but I haven't been approved yet. Re the Tamiya 50590 ball joints you used. Do you happed to have the STL for the Bearing Hubs you made? as am going to use your solution and buy the Tamiya parts.
Thanks Brian
I would ask you one the facebook group, but I haven't been approved yet. Re the Tamiya 50590 ball joints you used. Do you happed to have the STL for the Bearing Hubs you made? as am going to use your solution and buy the Tamiya parts.
Thanks Brian
-
- Posts: 4
- Joined: Fri Jun 28, 2019 3:07 pm
Re: Agera RS powered by Spezialbenzin
Hello Brian,
take a look at the file i added.
take a look at the file i added.
- Attachments
-
- Bearing_Hub_L_R_Tamiya_Balls.stl
- (133.38 KiB) Downloaded 204 times
Greetings from Germany,
Jürgen
Jürgen
- nitewatchman
- Posts: 8
- Joined: Thu Aug 02, 2018 1:10 am
Re: Agera RS powered by Spezialbenzin
I modified the Bearing Hubs to work with HobbyKing Ball Studs with a 2mm thread shank. HobbyKing SKU number is 110BS-30810.
Three 2mm Brass Inserts were heat set into the part and the Ball Studs screwed in. The modified Bearing Hubs are pretty close as the Link between the Upper and Lower Wishbones did not require any modification.
gary
Three 2mm Brass Inserts were heat set into the part and the Ball Studs screwed in. The modified Bearing Hubs are pretty close as the Link between the Upper and Lower Wishbones did not require any modification.
gary
- Attachments
-
- IMG_20190806_211137112 (Medium).jpg (145.89 KiB) Viewed 4239 times
-
- IMG_20190806_211212144 (Medium).jpg (171.72 KiB) Viewed 4239 times
-
- IMG_20190806_211220966 (Medium).jpg (154.61 KiB) Viewed 4239 times
-
- IMG_20190806_211311588 (Medium).jpg (152.62 KiB) Viewed 4239 times
-
- Bearing Hub Right 8x4x3BB (Cut 1) (Cut 2).stl
- (115.61 KiB) Downloaded 242 times
-
- Bearing Hub Left 8x4x3BB (Cut 1) (Cut 2).stl
- (115.61 KiB) Downloaded 261 times
Who is online
Users browsing this forum: No registered users and 0 guests